C:\Users\Patrick\Documents\Atmel\openocd-0.7.0\bin>openocd-0.7.0 -f scripts\inte
rface\usbprog.cfg -f scripts\target\at91sam3sXX.cfg
Open On-Chip Debugger 0.7.0 (2013-05-05-10:41)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.sourceforge.net/doc/doxygen/bugs.html
Warn : Adapter driver 'usbprog' did not declare which transports it allows; assu
ming legacy JTAG-only
Info : only one transport option; autoselect 'jtag'
tms sequence is  long
adapter speed: 500 kHz
adapter_nsrst_delay: 100
jtag_ntrst_delay: 100
cortex_m3 reset_config sysresetreq
Info : USB JTAG Interface ready!
Info : This adapter doesn't support configurable speed
Error: JTAG scan chain interrogation failed: all zeroes
Error: Check JTAG interface, timings, target power, etc.
Error: Trying to use configured scan chain anyway...
Error: sam3.cpu: IR capture error; saw 0x00 not 0x01
Warn : Bypassing JTAG setup events due to errors
Warn : Invalid ACK 0 in JTAG-DP transaction
Polling target sam3.cpu failed, GDB will be halted. Polling again in 100ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 300ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 700ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 1500ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 3100ms

C:\Users\Patrick\Documents\Atmel\openocd-0.7.0\bin>openocd-0.7.0 -f scripts\inte
rface\usbprog.cfg -f scripts\target\at91sam3sXX.cfg
Open On-Chip Debugger 0.7.0 (2013-05-05-10:41)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.sourceforge.net/doc/doxygen/bugs.html
Warn : Adapter driver 'usbprog' did not declare which transports it allows; assu
ming legacy JTAG-only
Info : only one transport option; autoselect 'jtag'
tms sequence is  long
adapter speed: 500 kHz
adapter_nsrst_delay: 100
jtag_ntrst_delay: 100
cortex_m3 reset_config sysresetreq
Info : USB JTAG Interface ready!
Info : This adapter doesn't support configurable speed
Info : JTAG tap: sam3.cpu tap/device found: 0xffffffff (mfg: 0x7ff, part: 0xffff
, ver: 0xf)
Warn : JTAG tap: sam3.cpu       UNEXPECTED: 0xffffffff (mfg: 0x7ff, part: 0xffff
, ver: 0xf)
Error: JTAG tap: sam3.cpu  expected 1 of 1: 0x4ba00477 (mfg: 0x23b, part: 0xba00
, ver: 0x4)
Warn : Unexpected idcode after end of chain: 480 0x000000ff
Warn : Unexpected idcode after end of chain: 512 0x00000000
Warn : Unexpected idcode after end of chain: 544 0x00000000
Warn : Unexpected idcode after end of chain: 576 0x00000000
Warn : Unexpected idcode after end of chain: 608 0x00000000
Error: double-check your JTAG setup (interface, speed, missing TAPs, ...)
Error: Trying to use configured scan chain anyway...
Error: sam3.cpu: IR capture error; saw 0x00 not 0x01
Warn : Bypassing JTAG setup events due to errors
Warn : Invalid ACK 0 in JTAG-DP transaction
Polling target sam3.cpu failed, GDB will be halted. Polling again in 100ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 300ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 700ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 1500ms
Polling target sam3.cpu failed, GDB will be halted. Polling again in 3100ms

C:\Users\Patrick\Documents\Atmel\openocd-0.7.0\bin>