Linux version 2.6.33.2 (root@debian) (gcc version 4.3.2 (GCC) ) #2 Mon Aug 19 05:55:09 EDT 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: In-Circuit ICnova G45
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c03bcee4, node_mem_map c03df000
  Normal zone: 256 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 32512 pages, LIFO batch:7
Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: rootfstype=ext2 root=/dev/mmcblk0p1 console=ttyS0,115200n8 rootwait ro
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125824KB available (3472K code, 300K data, 144K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:256
AT91: 160 gpio irqs in 5 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource pit
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 246
alg: No test for stdrng (krng)
io scheduler noop registered (default)
atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at 779c0000 (mapped at ffa00000)
Console: switching to colour frame buffer device 40x30
atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00500000 (mapped at c88bc000), irq 23
atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfff90000 (irq = 8) is a ATMEL_SERIAL
atmel_usart.3: ttyS3 at MMIO 0xfff94000 (irq = 9) is a ATMEL_SERIAL
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "atmel_nand":
0x000000000000-0x000000200000 : "Kernel"
0x000000200000-0x000001200000 : "Root"
0x000001200000-0x000010000000 : "Data"
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14)
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffbc000 irq 25 (00:1f:e5:00:4a:e3)
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00, irq=-1)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
Initializing Atmel-SoC USB Host Controller
atmel-ehci atmel-ehci: start
atmel-ehci atmel-ehci: Atmel EHCI UHP HS
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
atmel-ehci atmel-ehci: new USB bus registered, assigned bus number 1
atmel-ehci atmel-ehci: reset hcs_params 0x1202 dbg=0 cc=1 pcc=2 ordered !ppc ports=2
atmel-ehci atmel-ehci: reset hcc_params 0026 thresh 2 uframes 256/512/1024 park
atmel-ehci atmel-ehci: park 0
atmel-ehci atmel-ehci: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
atmel-ehci atmel-ehci: irq 22, io mem 0x00800000
atmel-ehci atmel-ehci: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
atmel-ehci atmel-ehci: init command 010009 (park)=0 ithresh=1 period=256 RUN
atmel-ehci atmel-ehci: USB 2.0 started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Atmel EHCI UHP HS
usb usb1: Manufacturer: Linux 2.6.33.2 ehci_hcd
usb usb1: SerialNumber: atmel-ehci
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
drivers/usb/core/inode.c: creating file '001'
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
at91_ohci at91_ohci: start
at91_ohci at91_ohci: AT91 OHCI
drivers/usb/core/inode.c: creating file '002'
at91_ohci at91_ohci: new USB bus registered, assigned bus number 2
at91_ohci at91_ohci: supports USB remote wakeup
at91_ohci at91_ohci: irq 22, io mem 0x00700000
at91_ohci at91_ohci: created debug files
at91_ohci at91_ohci: OHCI controller state
at91_ohci at91_ohci: OHCI 1.0, NO legacy support registers
at91_ohci at91_ohci: control 0x083 HCFS=operational CBSR=3
at91_ohci at91_ohci: cmdstatus 0x00000 SOC=0
at91_ohci at91_ohci: intrstatus 0x00000004 SF
at91_ohci at91_ohci: intrenable 0x8000005a MIE RHSC UE RD WDH
at91_ohci at91_ohci: hcca frame #0005
at91_ohci at91_ohci: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
at91_ohci at91_ohci: roothub.b 00000000 PPCM=0000 DR=0000
at91_ohci at91_ohci: roothub.status 00008000 DRWE
at91_ohci at91_ohci: roothub.portstatus [0] 0x00000100 PPS
at91_ohci at91_ohci: roothub.portstatus [1] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: AT91 OHCI
usb usb2: Manufacturer: Linux 2.6.33.2 ohci_hcd
usb usb2: SerialNumber: at91
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: no over-current protection
hub 2-0:1.0: power on to power good time: 4ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
drivers/usb/core/inode.c: creating file '001'
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
mice: PS/2 mouse device common for all mice
setting trigger mode 2 for irq 81 failed (gpio_irq_type+0x0/0x1c)
ads7846 spi0.2: trying pin change workaround on irq 81
ads7846 spi0.2: touchscreen, irq 81
input: ADS7846 Touchscreen as /class/input/input0
i2c /dev entries driver
Registered led device: pwr
Registered led device: LED1
Registered led device: LED2
Registered led device: LED3
Registered led device: LED4
at_hdmac at_hdmac: Atmel AHB DMA Controller ( cpy slave ), 8 channels
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
atmel_mci atmel_mci.0: Using dma0chan0 for DMA transfers
atmel_mci atmel_mci.0: Atmel MCI controller at 0xfff80000 irq 11, 1 slots
Waiting for root device /dev/mmcblk0p1...
mmc0: new SDHC card at address b368
mmcblk0: mmc0:b368 USD   7.46 GiB (ro)
 mmcblk0: p1 p2
VFS: Mounted root (ext2 filesystem) readonly on device 179:1.
Freeing init memory: 144K
eth0: link up (100/Full)
eth0: no IPv6 routers present